Sipsey in the Bankhead, Cheaha and Dugger Mountain in the Talladega, designated between 1977 and 1999. Motors and mechanised equipment are barred from all three
Two All-American Roads, the Natchez Trace Parkway and the Selma to Montgomery March Byway, and two National Scenic Byways, the Talladega Scenic Drive and Alabama’s Coastal Connection
Scenic drive the Forest Service publishes for the state 22
1
The Talladega Scenic Drive is the only named driving route across all four Alabama national forests. Everything else is an unnamed forest road on a motor vehicle use map
The Talladega Scenic Drive, as FHWA measures it 33
26.4 mi
The Forest Service gives the same byway as 29 miles. FHWA allows an hour for it and charges a dollar a person for the side trip into Cheaha State Park
Of Pinhoti National Recreation Trail in the Talladega 23
140 mi
Piedmont to Sylacauga, in the forest’s own Talladega handout. The same forest’s wilderness page calls it 100 miles of moderate to difficult hiking. It is a walking trail, not a driving one
Combined length of the Black Warrior and Tombigbee lakes 35
457 mi
Six lakes, Demopolis, Coffeeville, Warrior, Oliver, Holt and Bankhead, and 39,800 surface acres of water, all of it Mobile District
Approximately, on the coast beside Gulf State Park and the Coastal Connection byway. No vehicle may be driven on the sand anywhere along it
Armour, racks and knowing the real hazard
Alabama rewards restraint in steel. The places a full-size rig gets hurt are the unmaintained forest roads the Bankhead warns about, where the risks are ruts after a 5.46-inch December and low limbs on roads that see little traffic. Skid plates and sliders earn their keep. A body that hangs wide does not.
The other job here is the trailer. With only two designated OHV trails in the state, anybody who wants to ride is hauling a narrow machine to Kentuck or Double Springs. Tie-downs, ramp gates and a rack that survives 56 inches of annual rain without rusting matter more than a bumper that will never touch rock.
When a catalog part does not exist for your vehicle, does not fit with what you already have, or is not strong enough for what you do, a fabricator builds it. Steel or aluminum, welded, finished, and mounted so the load goes into structure rather than sheet metal.
They also fix what breaks: cracked mounts, bent sliders, torn brackets and the frame damage that ends trips.
Common work
01Bumpers with winch mounts and rated recovery points
02Rock sliders and skid plates
03Roof racks, bed racks and ladders
04Swing-outs for tires, fuel and water
05Mounts for tanks, compressors and batteries
06Frame and bracket repair
How to choose a fabricator
Metalwork is easy to judge if you know where to look.
01Look at the welds, then at how the part mounts. Recovery points and sliders should tie into the frame.
02Ask whether they design in CAD or build to the vehicle, and whether you get drawings.
03Ask about material and finish. Raw, painted and powder coated parts age very differently.
04Ask if they have built for your platform before. Templates and fixtures save you money.
05Ask how a front bumper affects airbag sensors and crush zones. A shop that has done it properly will have an answer.
What to have ready before you ask for a quote
Photographs do most of the talking.
01Clear photos of the vehicle and the area the part mounts to
02What is already mounted there: winch model, lights, tire size
03What the part has to carry, and how much it weighs
04Steel or aluminum, and the finish you want
05A budget range and your timing
Questions people ask
Custom or off the shelf?
If a well-made part exists for your vehicle, it is usually cheaper and faster than custom, and a good fabricator will tell you so. Custom earns its cost when nothing fits, when parts from different makers have to work together, or when you need it stronger or lighter than the catalog offers.
Steel or aluminum?
Steel is stronger for the money, easier to repair in the field and heavier. Aluminum saves real weight on racks, skid plates and boxes, but costs more and needs a welder who works with it regularly. Many builds use both: steel where it hits rocks, aluminum where it just carries things.
Can a fabricator repair a cracked frame or mount?
Often, yes. Send clear photos with your request. A good shop will tell you whether it can be repaired properly or needs replacing.
How high is Alabama?
From Gulf Shores at 7 feet to Cheaha Mountain at 2,407.
Altitude decides what your engine, your brakes and your lungs have to work with, and how late in the year the passes open.
02,000
Feet above sea level
Towns
HeflinCleburne County seat at 960 feet on US 78 and Interstate 20. The Shoal Creek Ranger District office is here, and the Talladega Scenic Drive leaves State Route 281 just west of town.960 ft
Fort PayneDeKalb County seat at 905 feet under Lookout Mountain. DeSoto State Park is eight miles northeast and the Little River Canyon Rim Parkway runs south from the falls.905 ft
Double SpringsWinston County seat and the Bankhead Ranger District office on Highway 33. Flint Creek, one of the state’s two OHV trails, is run from here.824 ft
AnnistonCalhoun County seat between the Shoal Creek and Talladega districts. The largest services stop within reach of Dugger Mountain, Choccolocco and the northern Pinhoti.711 ft
GuntersvilleMarshall County seat at 637 feet on the Tennessee River. Lake Guntersville State Park covers 6,000 acres of woodland above town with 36 miles of trail.637 ft
TalladegaTalladega Ranger District office, and the way up to Lake Chinnabee, Turnipseed and the Kentuck trail. Last town of any size on the west side of the Cheaha high ground.555 ft
FlorenceLauderdale County on the north bank of the Tennessee River. The Natchez Trace Parkway crosses this county between mileposts 328 and 342 before it leaves for Tennessee.550 ft
TuscumbiaColbert County seat south of the river. The parkway runs the length of this county from milepost 309 to 328, with the Colbert Ferry site on the Tennessee River at 327.3.468 ft
TuskegeeMacon County seat beside the smallest national forest in the country, which allows primitive camping anywhere outside gun deer season. Taska Recreation Area is 3.5 miles east on US 80 and 29.462 ft
AndalusiaCovington County seat and the Conecuh Ranger District office on Alabama Highway 55. Fuel and tyres before Open Pond, Blue Lake and the Florida line.345 ft
EufaulaBarbour County on the Chattahoochee, beside Walter F. George Lake and its 640 miles of shoreline, 13 Corps day use parks and four campgrounds.263 ft
BrentBibb County, and the Oakmulgee Ranger District office on Highway 5. The way in to Payne Lake, the Vick and South Sandy ranges and the district’s ten year-round hunting camps.241 ft
MontgomeryThe Forest Service supervisor’s office for all four Alabama national forests is on Chestnut Street. East end of the Selma to Montgomery March Byway and the nearest city to Horseshoe Bend.238 ft
SelmaDallas County seat at 137 feet on the Alabama River. West end of the 54-mile All-American Road to Montgomery, and close to the Corps lakes on the middle river.137 ft
DemopolisMarengo County, where the Tombigbee meets the Black Warrior. Corps resource manager’s office two miles west on US 80, and the south end of the Tennessee-Tombigbee river section.125 ft
Gulf ShoresSeven feet above the Gulf. Gulf State Park and its 496 improved campsites, the east end of Alabama’s Coastal Connection, and a city ordinance that bans every motor vehicle from the sand.7 ft
Passes, high roads and summits
Cheaha MountainTalladega Scenic Drive: US 78 west of Heflin to Adams Gap, on State Route 2812,407 ft
Dugger MountainCalhoun County, in the Dugger Mountain Wilderness on the Shoal Creek district. Measured for this chart from the 3DEP surface; no agency publishes a figure for it2,134 ft
Monte Sano MountainMadison County above Huntsville, the north end of the same ridge country. Our own 3DEP reading, not an agency figure1,654 ft
Adams GapClay County, where the pavement of the Talladega Scenic Drive ends and Forest Service Road 600 begins. Our own 3DEP reading1,443 ft
Pass, road and summit elevations are the figures published by the agency that manages them. Town elevations are the town’s or county’s own
figure where it publishes an exact one; the rest are from the U.S. Geological Survey (3D Elevation Program at the place’s official coordinates),
retrieved September 18, 2026. Every source is listed at the foot of the page.
Free build quotes
Looking for fabricators in Alabama? Tell us about the project and get free quotes.