Across 44.5 million acres, which is why the gaps between services are long
Steel that earns its weight on the prairie
There is little rock to bash in North Dakota, so heavy armor mostly costs you fuel. What is worth fabricating is anything that helps you get unstuck alone: rated recovery points front and rear, a shovel mount, a board mount you can reach without unpacking, and a spare carrier that takes a full-size tire.
Think about mud clearance too. Gumbo packs into tight gaps between tire and body and between frame and skid, so ask a fabricator to leave room to clean it out and to avoid shelves that collect clay and freeze solid overnight.
When a catalog part does not exist for your vehicle, does not fit with what you already have, or is not strong enough for what you do, a fabricator builds it. Steel or aluminum, welded, finished, and mounted so the load goes into structure rather than sheet metal.
They also fix what breaks: cracked mounts, bent sliders, torn brackets and the frame damage that ends trips.
Common work
01Bumpers with winch mounts and rated recovery points
02Rock sliders and skid plates
03Roof racks, bed racks and ladders
04Swing-outs for tires, fuel and water
05Mounts for tanks, compressors and batteries
06Frame and bracket repair
How to choose a fabricator
Metalwork is easy to judge if you know where to look.
01Look at the welds, then at how the part mounts. Recovery points and sliders should tie into the frame.
02Ask whether they design in CAD or build to the vehicle, and whether you get drawings.
03Ask about material and finish. Raw, painted and powder coated parts age very differently.
04Ask if they have built for your platform before. Templates and fixtures save you money.
05Ask how a front bumper affects airbag sensors and crush zones. A shop that has done it properly will have an answer.
What to have ready before you ask for a quote
Photographs do most of the talking.
01Clear photos of the vehicle and the area the part mounts to
02What is already mounted there: winch model, lights, tire size
03What the part has to carry, and how much it weighs
04Steel or aluminum, and the finish you want
05A budget range and your timing
Questions people ask
Custom or off the shelf?
If a well-made part exists for your vehicle, it is usually cheaper and faster than custom, and a good fabricator will tell you so. Custom earns its cost when nothing fits, when parts from different makers have to work together, or when you need it stronger or lighter than the catalog offers.
Steel or aluminum?
Steel is stronger for the money, easier to repair in the field and heavier. Aluminum saves real weight on racks, skid plates and boxes, but costs more and needs a welder who works with it regularly. Many builds use both: steel where it hits rocks, aluminum where it just carries things.
Can a fabricator repair a cracked frame or mount?
Often, yes. Send clear photos with your request. A good shop will tell you whether it can be repaired properly or needs replacing.
How high is North Dakota?
From Walhalla at 981 feet to White Butte at 3,506.
Altitude decides what your engine, your brakes and your lungs have to work with, and how late in the year the passes open.
02,0004,000
Feet above sea level
Towns
BowmanServices in the southwest where US 12 meets US 85. Much of the BLM’s North Dakota public land lies in this county and in Dunn.2,969 ft
BeachThe first town inside North Dakota on I-94 from Montana, at the west end of the badlands.2,769 ft
BelfieldWhere US 85 meets I-94. The North Unit entrance is 50 miles north up US 85, through grassland and oil country.2,582 ft
DickinsonFull services on I-94 and the home of the BLM’s North Dakota Field Office, which manages about 58,000 acres of public land and the mineral estate under the western third of the state.2,412 ft
KilldeerUnder the Killdeer Mountains, which the Geological Survey says stand about 700 feet above the plains around them. Little Missouri State Park and its horse trails are north of town.2,285 ft
MedoraThe gateway to the South Unit of Theodore Roosevelt National Park, where the 36-mile paved scenic loop starts and ends. Rough Rider State Park and the Maah Daah Hey Trail are minutes away.2,268 ft
Watford CityServices for the North Unit, 14 miles south on US 85, and for the north end of the Maah Daah Hey Trail at the CCC Campground about 16 miles south.2,123 ft
GarrisonNorth of Lake Sakakawea and Garrison Dam, near the Army Corps of Engineers campgrounds at Wolf Creek and East Totten Trail.1,925 ft
New TownOn the north side of Lake Sakakawea, between the badlands and the Minot road.1,901 ft
WillistonThe main town of the northwest, with Fort Union Trading Post National Historic Site out on Highway 1804 toward the Montana line.1,876 ft
BismarckState capital and home of the Dakota Prairie Grasslands Supervisor’s Office. Kimball Bottoms, the Corps of Engineers motorized play area, is eight miles south.1,694 ft
MandanAcross the Missouri from Bismarck. The 22-mile Roughrider OHV Trail runs south from Fort Abraham Lincoln State Park along Highway 1806.1,648 ft
BottineauServices for the Turtle Mountain State Recreation Area, about six miles northeast, which keeps motorized trail open to off-highway vehicles.1,637 ft
MinotThe largest city in the north, on US 2 and US 83, between the badlands and the Turtle Mountains. Des Lacs National Wildlife Refuge and its 10,500 acres lie northwest.1,614 ft
Valley CityOn I-94 where it crosses the Sheyenne River, in the country served by the Sheyenne River Valley Scenic Byway.1,221 ft
WalhallaThe town at the Pembina Gorge, where the state park keeps the only off-highway vehicle campground in the North Dakota park system.981 ft
Passes, high roads and summits
White ButteThe highest point in North Dakota, in Slope County. The USGS publishes 3,506 feet; our own reading of the elevation surface at its map point gives 3,5073,506 ft
Black ButteA badlands summit in Slope County, west of White Butte3,461 ft
Sentinel ButteIn Golden Valley County, west of Medora and south of I-943,426 ft
Bullion ButteA flat-topped butte in Billings County, south of Medora3,339 ft
Killdeer MountainsThe high point of the Killdeer Mountains, which the Geological Survey says stand as much as 1,000 feet above the Little Missouri floodplain3,314 ft
Pretty ButteIn western Slope County, near the Montana line3,171 ft
Pass, road and summit elevations are the figures published by the agency that manages them. Town elevations are the town’s or county’s own
figure where it publishes an exact one; the rest are from the U.S. Geological Survey (3D Elevation Program at the place’s official coordinates),
retrieved September 18, 2026. Every source is listed at the foot of the page.
Free build quotes
Looking for fabricators in North Dakota? Tell us about the project and get free quotes.
